Allen-Bradley PowerFlex 527 Скачать руководство пользователя

Страница: 83 / 176

Rockwell Automation Publication 520-UM002B-EN-E - December 2017

Configuring the PowerFlex 527 Drive with Integrated Motion

Chapter 3

Test and Tune the Axes –
Velocity and Position Control
Modes

This procedure assumes that you have configured your PowerFlex 527 drive, your
Logix5000 controller, and applied power to the system.

For help using the Logix Designer application as it applies to testing and tuning
your axes with ControlLogix EtherNet/IP modules or CompactLogix 5370
controllers, see

Additional Resources on page 9

Test the Axes

Note:

In the following example, the Axis Configuration is set to Position Loop.

Follow these steps to test the axes.

Verify the load was removed from each axis.

In your Motion Group folder, right-click an axis and choose Properties.

The Axis Properties dialog box appears.

Click the Hookup Tests category.

IMPORTANT

Before proceeding with testing and tuning your axes, verify that the MOD and
NET status indicators are operating as described in

PowerFlex 527 Drive Status

Indicators on page 126

ATTENTION:

Verify if drive I/O connection is in the running state and the axis is

in a stopped state

Содержание PowerFlex 527

















































































































































































Результаты поиска

Содержание PowerFlex 527

Отзывы:

Похожие инструкции для PowerFlex 527

Бренды по названию

Популярные бренды

Allen-Bradley PowerFlex 527, Руководство пользователя

Результаты поиска

Содержание PowerFlex 527

Отзывы:

Похожие инструкции для PowerFlex 527

Бренды по названию

Популярные бренды