Allen-Bradley PowerFlex 527 Скачать руководство пользователя | Manualshive

Страница: 113 / 176

background image

Rockwell Automation Publication 520-UM002B-EN-E - December 2017

113

Network Control of Safe Torque-Off

Chapter 6

Replacement with “Configure Always” Enabled

When the Configure Always feature is enabled, the controller automatically
checks for and connects to a replacement drive that meets all of the following
requirements:

•

The controller has configuration data for a compatible drive at that
network address.

•

The drive is in the Out-of-box condition or has an SNN that matches the
configuration.

If the project is configured for Configure Always, follow the appropriate steps to
replace a PowerFlex 527 drive.

Follow these steps when the Configure Always feature is enabled.

1.

Remove and replace the existing integrated safety drive.

2.

Right-click the replacement drive and choose Properties.

ATTENTION:

Enable the Configure Always feature only if the entire integrated

safety control system is not being relied on to maintain SIL 3 behavior during
the replacement and functional testing of a PowerFlex 527 drive. Do not place
drives that are in the Out-of-box condition on an integrated safety network
when the Configure Always feature is enabled, except while following this
replacement procedure.

If

Then

The drive is in the Out-of-box condition

Go to step 6.
No action is needed for the GuardLogix controller to take
ownership of the drive.

An SNN mismatch error occurs

Go to the next step to reset the drive to the Out-of-box
condition.

«
...
111
112
113
114
115
...
»

Содержание PowerFlex 527

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerFlex 527

Бренд: Abicor Binzel Страницы: 8

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 10

Бренд: Danfoss Страницы: 20

Бренд: Nedap Страницы: 20

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: Watts Страницы: 8

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA SIEMENS Страницы: 373

Бренд: WAGNER Страницы: 60

Бренд: PUTCO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды