manualshive.com logo in svg

AirLive ARM-104 V3, Руководство пользователя

Поделиться
Скачать
AirLive ARM-104 V3 Скачать руководство пользователя страница 98

 

AirLive

 

ARM-104_v3

 ADSL2/2+ Router

 

92

 

4.4.5.2 IP Filters – Custom IP Filters   

 

Customer IP Filters 

are different from Port forwards, or Block All traffic because they allow greater scopes of 

IP addresses to be included in the block. 

 

The Custom IP Filters function allows creation of up to 20 custom IP filtering entries to block specific services 

or applications based on: 

„

 

Source/Destination IP address and Netmask 

„

 

TCP Port (ranges supported) 

„

 Protocol 

„

 TCP 

„

 UDP 

„

 TCP 

and 

UDP 

„

 ICMP 

„

 Any 

 

 

 

„

 

Filter Name: 

Name of the IP filter rule you are about to create. 

„

 

Enable: 

The Enable button is checked by default, meaning this rule is applied when you click on 

the Apply button. 

„

 

Source IP: 

Since IP filtering is for outgoing traffic, the source IP is the IP address on your LAN 

side that you want to block network traffic from. 

„

 

Source Netmask: 

Netmask of the source IP on your LAN side. 

Содержание ARM-104 V3





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды