AirLive ARM-104 V3 Скачать руководство пользователя страница 68

Страница: 68 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

4.3.2.1.2 LAN Configuration - Unmanaged

The LAN Group Configuration screen allows you to configure settings for each defined LAN group. Notice

that you can also view the status of advanced services that can be applied to this LAN group.

Unmanaged:

Click the

Unmanaged

radio button, the following configuration screen will pop-up. All filling

items are hidden except the

Server and Relay Off

(Unchangeable) radio button will turn on.

Unmanaged

is a state when the LAN group is not configured and no IP address has been assigned to the

bridge.

Click the

Services

items will guides you to detail setting. Refer to

ADVANCED

section for

setting/configuration details.

Apply:

Click

Apply

to complete the setting.

Cancel:

Click

Cancel

to ignore all the changes.

To complete and save the setting, click

Save All

after clicking the

Apply

button.

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды