AirLive ARM-104 V3 Скачать руководство пользователя страница 17

Страница: 17 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

2.2 Back Panel:

The back panel of the

ARM-104_v3

ADSL2/2+ Router contains ADSL, Ethernet Switches, Reset and Power

Adapter connection.

ADSL

Port for connecting to the ADSL2/2+ Service Provider.

Ports 1~4

Four 10/100Mbps Ethernet Ports for connecting to the network devices

RESET

Restore the

ARM-104_v3

ADSL2/2+ Router to factory default setting.

POWER

12V DC/1A or 9V AC/1A Power adapter connector.

Resetting Factory Defaults:

The reboot and restore to factory defaults feature will set the device to its factory default configuration by

resetting the

ARM-104_v3

ADSL2/2+ Router.

To Reset the

ARM-104_v3

ADSL2/2+ Router:

Ensure that the device is powered on.

Press the Reset button for 10~15 seconds and release. Wait for 30 seconds after release the Reset

button. Do not power off the device during the reset process.

The default settings are now restored after 30 seconds.

All the Ethernet port of the ARM-104_v3 ADSL2/2+ Router supports

auto-crossover capability.

RESET Button:

Reboot & Restore the

ARM-104_v3

ADSL2/2+ Router to factory defaults.

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды