AirLive ARM-104 V3 Скачать руководство пользователя страница 20

Страница: 20 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

Chapter 3 Setting up the TCP/IP in Windows

The instruction in this chapter will help you configure your computers to be able to communicate with this

ARM-104_v3

ADSL2/2+ Router.

Computers access the Internet using a protocol called TCP/IP (Transmission Control Protocol/ Internet

Protocol). Each computer/notebook on your network must have TCP/IP installed and selected as its

networking protocol. If a Network Interface Card (NIC) is already installed in your PC, then TCP/IP is probably

already installed as well.

The following description assumes

ARM-104_v3

ADSL2/2+ Router been set to factory default. (If not, please

hold the reset button down for 5~10 seconds). The default of the

ARM-104_v3

ADSL2/2+ Router’s LAN IP is

192.168.1.1

Follow the procedures below to set your computer/notebook function as a

DHCP Client

Restart and Reboot your Windows system might be necessary after setting your
computer function as a DHCP Client. In order to properly activate your choice, click
“OK” to restart your Windows system.

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды