manualshive.com logo in svg

AirLive ARM-104 V3, Руководство пользователя

Поделиться
Скачать
AirLive ARM-104 V3 Скачать руководство пользователя страница 58

 

AirLive

 

ARM-104_v3

 ADSL2/2+ Router

 

52

 

4.3.1.1.5 New Connection - Bridge Connection Setup 

 

Bridge:

 When Bridge mode is selected, the following screen will pop-up. A Bridged connection basically 

disables the routing, firewall and NAT features of the 

ARM-104_v3

 ADSL2/2+ Router. In a Bridged 

connection, the 

ARM-104_v3

 ADSL2/2+ Router acts as a modem or hub, and just transmits packets between 

the WAN interface and the LAN interface. A Bridged connection assumes that another device is providing the 

routing functionality that is now disabled in the 

ARM-104_v3

 ADSL2/2+ Router. 

 

 

 

„

 

Name:

 Enter the Bridge connection name. The name must be unique and must not contain spaces 

and must not begin with a number. 

„

 

Type:

 Connection Type : 

Bridge

.  

„

 

Sharing:

 Select 

“Disable”

, 

“Enable”

 or 

“VLAN”

 sharing. Default setting is 

“Disable”

. The VLAN 

needs to be selected to create VLAN. 

„

 

Options: 

Click to enable 

“NAT”

 and/or

 “Firewall”

 functionality. Default is 

“Enable”

. 

„

 

VLAN ID:

 If 

“VLAN”

 is selected, manually enter the 

“VLAN ID”

 and select 

“Priority Bits”

 from 

the drop down manual. 

„

 

Priority Bits:

 Priority is given to a VLAN connection from 0-7, 0 being the highest priority. 

„

 

Bridge Settings: 

;

 

Encapsulation:

 Select the encapsulation type (LLC or VC) according to the information 

provided by the ISP. 

;

 

Select LAN: 

Up to three LAN Group can be specified. Select your LAN Group from the drop 

down manual. 

Содержание ARM-104 V3





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды