manualshive.com logo in svg

AirLive ARM-104 V3, Руководство пользователя

Поделиться
Скачать
AirLive ARM-104 V3 Скачать руководство пользователя страница 89

 

AirLive

 

ARM-104_v3

 ADSL2/2+ Router

 

83

 

4.4.4.1 Port Forwarding Configuration Procedure 

 

1. 

From the Port Forwarding configuration screen, select 

WAN Connection

, 

LAN Group

, and 

LAN IP

.  

 

If the desired LAN IP is not available in the LAP IP drop-down menu, you can add it using the LAN Client 

screen, which can be accessed by clicking 

NEW IP

.  

 

2. 

Select the available rules for a given category, click 

View 

to view the rule associated with a predefined 

filter (Figure below), click 

Add 

to apply the rule for this category. 

 

 

 

3. 

If a rule is not in the list, you can create your own in the user category. With User category selected, 

click 

Add

. The Rule Management screen will populate for you to create new rules. The rule(s) you 

create will be available in the User category. You will be able to Edit/Delete the rule(s) you create. 

 

 

 

Содержание ARM-104 V3





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды