manualshive.com logo in svg

AirLive ARM-104 V3, Руководство пользователя

Поделиться
Скачать
AirLive ARM-104 V3 Скачать руководство пользователя страница 115

 

AirLive

 

ARM-104_v3

 ADSL2/2+ Router

 

109

 

4.5 TOOLS 

 

Figure below shows the 

TOOLS

 main screen, which can be accessed by clicking on the 

TOOLS

 tab from the 

top of the screen. This screen provides access to the following tools screens: 

;

 System 

Commands 

;

 Remote 

Log 

;

 User 

Management 

;

 Update 

Gateway 

;

 Ping 

Test 

;

 Modem 

Test 

;

 Save 

All 

 

 

 

„

 

System Commands: 

Save the current configuration, restart the 

ARM-104_v3

 ADSL2/2+ Router 

and restore to factory defaults setting. 

„

 

Remote Log:

 Setup Remote Log Information. 

„

 

User Management:

 Configure user name and password. 

„

 

Update Gateway:

 Upgrade the 

ARM-104_v3

 ADSL2/2+ Router firmware. 

„

 

Ping Test:

 Run a ping test. 

„

 

Modem Test:

 Check whether the modem with a specific connection is properly connected to the 

network. 

„

 

Save All:

 Save the device setting. 

Содержание ARM-104 V3





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды