AirLive ARM-104 V3 Скачать руководство пользователя страница 19

Страница: 19 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

Following are the steps to properly connect your

ARM-104_v3

ADSL2/2+ Router:

1. Turn off your computer/notebook.

2. Connect the ADSL port of your

ARM-104_v3

ADSL2/2+ Router to the wall jack of the

ADSL/ADSL2/ADSL2+ Line with a RJ-11 cable.

3. Connect the Ethernet cable (RJ-45) from your

ARM-104_v3

ADSL2/2+ Router (Switch) to the Ethernet

Adaptor in your computer.

4. Connect the Power adaptor to the

ARM-104_v3

ADSL2/2+ Router and plug it into a Power outlet.

5. Turn on your computer.

6. Refer to the next section to setup or configure your system’s Network Adaptor.

The Power light will lit after turning on the

ARM-104_v3

ADSL2/2+

Router.

Auto and self-diagnostic process might turn the LED indicators ON and

OFF during the process.

Use the Power Adaptor exclusively in combination with the equipment

supplied and do not use any other kind of power adaptor for the

equipment.

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды