AirLive ARM-104 V3 Скачать руководство пользователя страница 75

Страница: 75 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

4.4 ADVANCED

The Advanced Menu provides access to advanced networking, management and routing capabilities.

Click the

ADVANCED

tab and the following screen will pop-up.

The Advanced tab allows you to perform advanced configuration functions for existing connections including:

Enabling and disabling of key features including SNTP, SNMP, IP QoS, RIP and multicasting.

Assignment of IP QoS weighting to connections.

Management of LAN port interfaces, packet flow, and filtering.

At least one WAN connection must be configured before implementing advanced WAN configuration features.

At least on LAN group must be defined before implementing advanced LAN configuration features.

SNTP:

Configure SNTP to configure time server on Internet.

SNMP:

Configure SNMP Management.

IP QoS:

Configure IP Quality of Service for different connections.

Port Forwarding:

Configure Firewall and NAT pass-through to your hosted applications.

IP Filters:

Configure Firewall to block your LAN PCs from accessing the Internet.

LAN Clients:

Configure LAN Clients.

LAN Isolation:

Disable traffic between LANs.

Bridge Filters:

Select to setup Bridge Filters.

Multicast:

Configure Multicast pass-through for different connections.

Static Routing:

Configure Static routes.

Dynamic Routing:

Configure RIP.

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды