AirLive ARM-104 V3 Скачать руководство пользователя страница 121

Страница: 121 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

115

4.5.4.1 Update Gateway Procedure

Use the following procedures to update firmware for your

ARM-104_v3

ADSL2/2+ Router.

1. Click

Browse

and select the file to update. The file name will appear in the Select a File field.

Note

—

The file size should not exceed 3.5MB.

2. Click

Update Gateway

. The status of the uploading will appear at the bottom of the screen. When the

upload is finished, the

ARM-104_v3

ADSL2/2+ Router will reboot and you will be prompt to log in again.

3. Enter

your

Username

and

Password

to log back in.

If you want to make sure the firmware is properly upgraded, go to

Status /Product Information

and

check on the Wireless Firmware version information on the Product Information screen

If you would like a copy of the configuration file (config.bin) saved to the

ARM-104_v3

ADSL2/2+ Router

flash, click

Get Configuration

to download it.

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды