AirLive ARM-104 V3 Скачать руководство пользователя страница 148

Страница: 148 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

142

VCI:

Virtual Channel Identifier: A virtual channel identified by a unique numerical tag that is defined by a

16-bit field in the ATM cell header. The purpose of the virtual channel is to identify where the cell should

travel.

VC-Mux:

Virtual Circuit based Multiplexing: In VC Based Multiplexing, the interconnect protocol of the carried

network is identified implicitly by the VC (Virtual Circuit) connecting the two ATM stations (each protocol must

be carried over a separate VC).

VPI:

Virtual Path Identifier: Virtual path for cell routing indicated by an eight bit field in the ATM cell header.

WAN:

Wide Area Network: A WAN covers a large geographical area. A WAN is consisted of LANs and the

Internet is consisted of WANs.

WPA:

Wi-Fi Protected Access (WPA) is a specification of standards-based, interoperable security

enhancements that increase the level of data protection and access control for existing and future wireless

LAN systems.

UI845_03

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды