manualshive.com logo in svg

AirLive ARM-104 V3, Руководство пользователя

Поделиться
Скачать
AirLive ARM-104 V3 Скачать руководство пользователя страница 82

 

AirLive

 

ARM-104_v3

 ADSL2/2+ Router

 

76

 

„

 

Trusted Mode:

 Click to enable Trusted Mode. The 

ARM-104_v3

 ADSL2/2+ Router has two 

primary modes of operation with regard to queue traffic prioritization - Trusted and Un-Trusted. 

This field allows you to choose the mode - Trusted (Checked) and Un-Trusted (Unchecked). 

In "Trusted Mode" all the rules will be applied first, regardless of the setting of the TOS bits. After   

the rules have been exhausted the existing TOS bit settings will be honored. The "Un-Trusted"   

mode will match first against all rules as in "Trusted" mode. The difference is that if there is no   

match then a default rule will be used. The default rule will have an associated queuing priority –   

Low. 

„

 

Apply: 

Click 

Apply

 to complete the setting. 

„

 

Cancel: 

Click 

Cancel 

to ignore all the changes. 

„

 

To complete and save the setting, click 

Save All 

after clicking the 

Apply

 button. 

Содержание ARM-104 V3





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды