AirLive ARM-104 V3 Скачать руководство пользователя страница 18

Страница: 18 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

2.3 Connection Mechanism:

This section describes the hardware connection mechanism of

ARM-104_v3

ADSL2/2+ Router on your Local

Area Network (LAN) connected to the Internet, how to configure your

ARM-104_v3

ADSL2/2+ Router for

Internet access or how to manually configure your Internet connection.

You need to prepare the following items before you can establish an Internet connection through your

ARM-104_v3

ADSL2/2+ Router:

1. A computer/notebook which must have an installed Ethernet Adaptor and an Ethernet Cable,

2. ADSL/ADSL2/ADSL2+

service

account and configuration information provided by your Internet Service

Provider (ISP). You will need one or more of the following configuration parameters to connect your

ARM-104_v3

ADSL2/2+ Router to the Internet:

a. VPI/VCI

parameters

Multiplexing Method or Protocol Type or Encapsulation Type

Host and Domain Names

ISP Login Name and Password

ISP Domain Name Server (DNS) Address

Fixed or Static IP Address.

Figure below shows the overall hardware connection mechanism of your

ARM-104_v3

ADSL2/2+ Router

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды