AirLive ARM-104 V3 Скачать руководство пользователя страница 38

Страница: 38 / 148

AirLive

ARM-104_v3

ADSL2/2+ Router

Connection Profile

(Normally show the ISP Name) will be added to the left side of the

configuration frame under

WAN Setup

NOTE:

If the final setting are differ from what you’d selected in

STEP 1

, click

EZ SETUP

Wizard

and redo

the setup procedures or else check your dealer immediately for technical support.

NOTE:

The

ARM-104_v3

ADSL2/2+ Router can be configured to maintain up to 8 Connection Profiles.

Different

Connection Profiles may be required if you connect to more than one ADSL service provider, or if you vary

the connection type/setting you use.

Note that in many cases, only one Connection Profile will be required and only one Connection Profile in used

at one time.

To complete and save the new Connection Profile, click the

Apply

button, and then click

Save All

Содержание ARM-104 V3





















































































































































Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-104 V3, Руководство пользователя

Результаты поиска

Содержание ARM-104 V3

Отзывы:

Бренды по названию

Популярные бренды