manualshive.com logo in svg

Air Monitor VELTRON DPT-plus, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Air Monitor VELTRON DPT-plus Скачать руководство пользователя страница 59

VELTRON DPT-

plus

Air Monitor Corporation

116-010-91.P65 (09/18/09)

VELTRON DPT-

plus

 - IO&M Manual

54

8 – TROUBLESHOOTING

SECTION 8 – TROUBLESHOOTING

Personnel should be familiar with the operation of the VELTRON DPT-

plus

 (see Section 5) before performing any

troubleshooting.

Note: Prior to performing any troubleshooting, turn power OFF.  After 10 seconds, turn power switch ON.  If problem

still exists, proceed with troubleshooting steps.

Problem

No Display and "CPU
Activated" 

•

 is not blinking.

No output or incorrect output
(Output 1 or 2) and display
responding correctly with
process change.

No output or incorrect output
(Output 1 or 2) and display
not responding or correctly
with process change.

AUTO-zero Function
is not working.

             is continuously lit.

             is flashing rapidly.

Alarms not working.

Process Signal is Unreliable
is displayed on Line 1 of
display.

Unreliable is displayed on
Line selected to display
Temperature.

Solution

– Verify input power is present at the correct voltage as listed on label and connected to

Terminals 15 and 16.

– Check fuse F1 (see Figure 4.4 for location).

– Review Factory Set-Up Information Sheet for type of output (isolated or non-isolated).
– Check terminal strip wiring for proper installation.
– Perform Transmitter Output Calibration (see Section 6).

– Verify pressure signal lines are connected correctly.
– Verify AUTO-zero valve switch is in the OFF position.
– Check for leaky or obstructed lines between 

VELTRON DPT-

plus

 and process sensor.

– Check for kinked internal signal pressure lines in transmitter base.

– Verify AUTO-zero is ON and interval is properly set (see Section 5.9).
– Verify AUTO-zero valve switch is in the OFF position.

– Zero value measured during AUTO-zero cycle is between 90 and 100% of span.  Transmitter

Input Calibration should be performed as soon as possible (see Section 6.3).

– Zero value measured during AUTO-zero cycle is greater than 100% of span.  Transmitter

Input Calibration should be performed immediately (see Section 6.3).

– Verify that Alarm is ON and setpoints are set to correct value (see Section 5.11).
– Check for proper terminal strip wiring and connections (see Section 4.5).

– Verify pressure signal lines are connected correctly (see Section 4.4).
– Verify process is operating within design parameters specified on Factory Set-Up Sheet.

– Verify temperature signal is connected properly according to the type of temperature device

(see Section 4.5).

– Verify temperature signal from temperature device is a 4.0-20.0mADC type.
– Verify temperature device is operating correctly.

If after following the Troubleshooting steps the VELTRON DPT-

plus

 continues to operate

improperly, contact the Service Department for further assistance (see Section 10).

zero

zero

Содержание VELTRON DPT-plus































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды