manualshive.com logo in svg

Air Monitor VELTRON DPT-plus, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Air Monitor VELTRON DPT-plus Скачать руководство пользователя страница 22

VELTRON DPT-

plus

Air Monitor Corporation

116-010-91.P65 (09/18/09)

VELTRON DPT-

plus

 - IO&M Manual

17

5.6 – CONFIGURATION PROGRAMMING

    

Note:

User selectable parameters are limited to standard features and those available for options installed at the
factory.  The following will detail all user parameters, which may or may not be available on your unit.

With power ON and initialization complete (see Section 5.2), press       and display will indicate:

   USER SETUP

Pressing       will enter the user into the Main Menu of configuration programming.  The display will indicate:

       Transmitter Scaling
        and Configuration

By using       and      , the user can scroll through the following selections:

SECTION 5 – OPERATION

MAIN MENU SELECTION

Transmitter Scaling & Configuration

Low Pass Filter Selection

AUTO-zero Configuration

AUTO-purge Configuration

Alarm Configuration

K-Factor Configuration

Display Configuration

Analog Output Configuration

Transducer Span Selection

Transmitter Input Calibration

Transmitter Output Calibration

Transducer Characterization Selection

Display Internal Temperature

Perform Transmitter Reset

Exit User Setup

DESCRIPTION

Allows for the configuration of process variable such as:  Density Compensation
Type, Square root, process type, process minimum/ maximum/units, duct area,
percent lockdown, and Temperature configuration. Also offers a Flow/D.P. calculator
that allows user to calculate maximum flow or differential pressure based on
entered variables.

Selects amount of filtering applied to transducer output.

Turns AUTO-zero function ON or OFF, and selects activation interval.

Refer to AUTO-purge Installation, Operation & Maintenance Manual for
configuration information.

Turns alarm function ON or OFF, select Alarm Type, High and Low Setpoints,
Deadband selection, and Alarm Delay.

Turns K-Factor ON or OFF, and allows for the calculation or selection of gain and
bias values.

Allows for the configuration of Display Parameters and Filters.

Allows for the selection of Analog Output 2 parameter.

Allows for displaying the natural span of the installed transducer, and selecting the
operating span.

Allows for the zeroing and spanning transmitter analog Inputs.

Allows for the zeroing and spanning of transmitter analog Outputs.

Allows transducer characterization data to be entered when transducer is replaced.

Allows for displaying the internal temperature of the VELTRON DPT-

plus

 unit.

Allows for restarting the transmitter in case of lock-up.

Returns display to 

Normal

 operation.

Содержание VELTRON DPT-plus































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды