Air Lift LoadLifter 7500 XL Скачать руководство пользователя страница 27

MN-1033

25

 

Clearance test — Inflate the air springs to 40-60 PSI (2 .8-4 .1BAR) and make sure 
there is at least 1/2” (13mm) clearance from anything that might rub against each 
sleeve . Be sure to check the tire, brakes, frame, shock absorbers and brake cables .

 

Leak test before road test — Inflate the air springs to 40-60 PSI (2 .8-4 .1BAR) and 
check all connections for leaks . All leaks must be eliminated before the vehicle is 
road tested .

 

Heat test — Be sure there is sufficient clearance from heat sources, at least 6” (152mm) 
for air springs and air lines . If a heat shield was included in the kit, install it . If there is no 
heat shield, but one is required, call Air Lift customer service at 

(800) 248-0892 .

 

Fastener test — Recheck all bolts for proper torque .

 

Road test — The vehicle should be road tested after the preceding tests . Inflate the 
air springs to recommended driving pressures . Drive the vehicle 10 miles (16km) and 
recheck for clearance, loose fasteners and air leaks .

 

Operating instructions — If professionally installed, the installer should review the 
operating instructions with the owner . Be sure to provide the owner with all of the 
paperwork that came with the kit .

INSTALLATION CHECKLIST

1 .  Check air pressure weekly .
2 .  Always maintain normal ride height . Never inflate beyond 100 PSI (7BAR) .
3 .  If the system develops an air leak, use a soapy water solution to check all air line 

connections and the inflation valve core before deflating and removing the air spring .  

FOR SAFETY AND TO PREVENT POSSIBLE DAMAGE TO THE VEHICLE, DO NOT EXCEED 
MAXIMUM GROSS VEHICLE WEIGHT RATING (GVWR) OR PAYLOAD RATING, AS INDICAT-
ED BY THE VEHICLE MANUFACTURER . 

ALTHOUGH THE AIR SPRINGS ARE RATED AT A MAXIMUM INFLATION PRESSURE OF 
100 PSI (7BAR), THE AIR PRESSURE ACTUALLY NEEDED IS DEPENDENT ON LOAD AND 
GROSS VEHICLE WEIGHT RATING .

Maximum Air Pressure

Minimum Recommended Pressure

100 PSI (7BAR)

5 PSI (.34BAR)

CAUTION

CAUTION

H. Maintenance and Use Guidelines

Limited Warranty and Return Policy

Air Lift Company provides a limited lifetime warranty to the original purchaser of its load support 
products, that the products will be free from defects in workmanship and materials when used 
on cars and trucks as specified by Air Lift Company and under normal operating conditions, 
subject to the requirements and exclusions set forth in the full Limited Warranty and Return 
Policy that is available at 

www.airliftcompany.com/warranty . 

For additional warranty information contact Air Lift Company customer service .

G. Before Operating

LoadLifter 7500 

XL

25

Содержание LoadLifter 7500 XL





























Отзывы: