Agilent Technologies G4782A Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 202

background image

1260 SFC Binary Pump

37

Using the Pump

3

Leak and Waste Handling

Leak and Waste Handling

For details on correct installation, see separate installation documentation.

WA R N I N G

Toxic, flammable and hazardous solvents, samples and reagents

The handling of solvents, samples and reagents can hold health and safety risks.

➔

When working with these substances observe appropriate safety procedures (for
example by wearing goggles, safety gloves and protective clothing) as described in
the material handling and safety data sheet supplied by the vendor, and follow
good laboratory practice.

➔

Do not use solvents with an auto-ignition temperature below 200 °C (392 °F). Do
not use solvents with a boiling point below 56 °C (133 °F).

➔

Avoid high vapor concentrations. Always keep the temperature in the sample
compartment at least 25 K below the boiling point of the solvent used.

➔

Do not operate the instrument in an explosive atmosphere.

➔

Reduce the volume of substances to the minimum required for the analysis.

➔

Never exceed the maximum permissible volume of solvents (8 L) in the solvent
cabinet. Do not use bottles that exceed the maximum permissible volume as
specified in the usage guideline for solvent cabinet.

➔

Ground the waste container.

➔

Regularly check the filling level of the waste container. The residual free volume in
the waste container must be large enough to collect the waste liquid.

➔

To achieve maximal safety, regularly check the tubing for correct installation.

N O T E

For details, see the usage guideline for the solvent cabinet. A printed copy of the guideline
has been shipped with the solvent cabinet, electronic copies are available in the Agilent
Information Center or via the Internet.

«
...
35
36
37
38
39
...
»

Содержание G4782A











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G4782A

Бренд: Waterous Страницы: 36

Бренд: Paragon Страницы: 16

MRV II AV08NMVERA

Бренд: Haier Страницы: 40

Бренд: Haier Страницы: 2

Бренд: Panasonic Страницы: 224

Бренд: GALAXY SPAS Страницы: 26

Бренд: Waterous Страницы: 10

Бренд: Oasis Страницы: 18

Clima Canal JDPC.002

Бренд: Jaga Страницы: 8

Бренд: Magnum Страницы: 16

Бренд: Kamco Страницы: 36

Бренд: AquaPRO Страницы: 4

Бренд: Daalderop Страницы: 16

Бренд: SPERONI Страницы: 68

Summit Pumper Vacuum

Бренд: Alto Страницы: 6

Бренд: Payne Страницы: 4

Бренд: SPX Страницы: 28

Altherma 3 R MT F+W

Бренд: Daikin Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды