Agilent Technologies G4782A Скачать руководство пользователя страница 36

Страница: 36 / 202

1260 SFC Binary Pump

Using the Pump

Best Practices

Prepare the pump

Purge

Use the Purge function to:

•

fill the pump,

•

exchange a solvent,

•

remove air bubbles in tubes and pump heads.

Seal wash

Seal Wash guarantees a maximum seal life time. Use Seal Wash:

•

When using buffers with elevated salt concentrations

•

When using volatile solvents with non-volatile additives

How to deal with solvents

•

Use clean bottles only.

•

Exchange water-based solvents daily.

•

Select solvent volume to be used up within 1 – 2 days.

•

Use only HPLC-grade solvents and water filtered through 0.2 μm filters.

•

Label bottles correctly with bottle content, and filling date / expiry date.

•

Use solvent inlet filters.

•

Reduce risk of algae growth: use brown bottles for aqueous solvents, avoid
direct sunlight.

C A U T I O N

Contaminated seal wash solvent

➔

Do not recycle seal wash solvent to avoid contamination.

➔

Weekly exchange seal wash solvent.

Содержание G4782A











































































































































































































Результаты поиска

Содержание G4782A

Отзывы:

Похожие инструкции для G4782A

Бренды по названию

Популярные бренды

Agilent Technologies G4782A, Руководство пользователя

Результаты поиска

Содержание G4782A

Отзывы:

Похожие инструкции для G4782A

Бренды по названию

Популярные бренды