Agilent Technologies G4782A Скачать руководство пользователя страница 108

Страница: 108 / 202

108

1260 SFC Binary Pump

Maintenance

Maintenance of a Pump Head without Seal Wash

Place the pump head on a flat surface. Loosen the lock
screw (two turns).

While holding the lower half of the assembly (piston
housing), carefully pull the pump housing away from the
piston housing.

Remove the support rings from the piston housing.

Lift the housing away from the pistons.

Check the piston surface and remove any deposits or
layers: clean the piston surface with abrasive paper and
rinse with 2-propanol. Replace piston if scratched.

Using the steel side of the insert tool, carefully remove
the seal from the pump housing.

3LVWRQ6XUIDFH

Содержание G4782A











































































































































































































Результаты поиска

Содержание G4782A

Отзывы:

Похожие инструкции для G4782A

Бренды по названию

Популярные бренды

Agilent Technologies G4782A, Руководство пользователя

Результаты поиска

Содержание G4782A

Отзывы:

Похожие инструкции для G4782A

Бренды по названию

Популярные бренды