manualshive.com logo in svg

Agilent Technologies B1542A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies B1542A Скачать руководство пользователя страница 48

2- 28

Agilent B1542A User’s Guide, Edition 4

Installation

Rack-mounting Pulse/dc Switch Units

Rack-mounting the Infiniium Oscilloscope

Rack-mount Infiniium oscilloscope as shown below. The required parts are included 
in the option B1542A-025 and the Agilent E2609B. See Figure 2-21.

Required parts:

Procedure:

1. Prepare the support rails available for your system rack, and secure them to the 

proper position of the system rack by using the typical rack-mounting method of 
the support rail kit.

2. Prepare the rack-mount kit 

A

, and assemble the oscilloscope panel. See 

Installation Guide of Agilent E2609B rack-mount kit for details.

3. Align the oscilloscope panel (oscilloscope with 

A

) with the support rails secured 

to the system rack in the step 1, gently slide the panel on the rails until it stops, 
and secure the panel to the system rack by using the typical rack-mounting 
method of the rack-mount flange kit.

Figure 2-21

Rack-mounting Infiniium Oscilloscope

Reference 

Designator

Agilent Model 

No. or Part No.

Quantity

Description

A

E2609B

1

Rack-mount kit for Infiniium 
oscilloscope, 5 EIA

B

B1542-01213

a

a. To rack-mount onto the 1181B system cart, use this support rail instead 

of the support rail included in the E2609B.

2

Support rail for rack-mounting 
oscilloscope onto 1181B

B

A

B

1

1

2

3

Содержание B1542A



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды