Agilent Technologies B1542A Скачать руководство пользователя страница 160

Страница: 160 / 162

7- 22

Agilent B1542A User’s Guide, Edition 4

Status Code and Error Messages

DVRSCOPE_INSTR_ERROR_PARAMETER6

BFFC0F15

-3861

Invalid value for parameter 6.

DVRSCOPE_INSTR_ERROR_PARAMETER7

BFFC0F16

-3862

Invalid value for parameter 7.

DVRSCOPE_INSTR_ERROR_PARAMETER8

BFFC0F17

-3863

Invalid value for parameter 8.

DVRSCOPE_INSTR_ERROR_PARAMETER9

BFFC0F18

-3864

Invalid value for parameter 9.

DVRSCOPE_INSTR_ERROR_PARAMETER10

BFFC0F19

-3865

Invalid value for parameter 10.

DVRSCOPE_INSTR_ERROR_PARAMETER11

BFFC0F1A

-3866

Invalid value for parameter 11.

DVRSCOPE_INSTR_ERROR_PARAMETER12

BFFC0F1B

-3867

Invalid value for parameter 12.

DVRSCOPE_INSTR_ERROR_PARAMETER13

BFFC0F1C

-3868

Invalid value for parameter 13.

DVRSCOPE_INSTR_ERROR_PARAMETER14

BFFC0F1D

-3869

Invalid value for parameter 14.

DVRSCOPE_INSTR_ERROR_PARAMETER15

BFFC0F1E

-3870

Invalid value for parameter 15.

DVRSCOPE_INSTR_ERROR_PARAMETER16

BFFC0F1F

-3871

Invalid value for parameter 16.

DVRSCOPE_ERROR_NO_CONFIG_FILE

BFFC0F20

-3872

Configuration file is not found.
Reinstall the pulsed IV software.

DVRSCOPE_ERROR_PERMISSION_CONFIG_FIL
E

BFFC0F21

-3873

Configuration file permission error.
Set read permission for this user.

DVRSCOPE_ERROR_AN_ERROR_ON_CONFIG_F
ILE

BFFC0F22

-3874

Configuration file open error.
Reinstall the pulsed IV software.

DVRSCOPE_ERROR_KEYWORD_ON_CONFIG_FI
LE

BFFC0F23

-3875

Configuration file keyword error.
Reinstall the pulsed IV software.

DVRSCOPE_ERROR_GPIB_NUM_ON_CONFIG_FI
LE

BFFC0F24

-3876

Invalid GPIB description. Reinstall
the pulsed IV software.

DVRSCOPE_ERROR_ADDR_ON_CONFIG_FILE

BFFC0F25

-3877

Invalid BUS address. Reinstall the
pulsed IV software.

DVRSCOPE_ERROR_SCOPE_TYPE_ON_CONFIG
_FILE

BFFC0F26

-3878

Invalid SCOPE type. Use the
supported instrument.

DVRSCOPE_ERROR_SCOPE_TYPE_NOT_MATCH

BFFC0F30

-3888

Instrument IDN does not match. Use
the supported instrument.

Status Code Name

Status

Code

Error

Number

Error Message

Содержание B1542A



































































































































































Результаты поиска

Содержание B1542A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies B1542A, Руководство пользователя

Результаты поиска

Содержание B1542A

Отзывы:

Бренды по названию

Популярные бренды