manualshive.com logo in svg

Agilent Technologies B1542A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies B1542A Скачать руководство пользователя страница 26

2- 6

Agilent B1542A User’s Guide, Edition 4

Installation

Hardware Installation

Hardware Installation

This section describes the instructions to install the B1542A. The installation 
instructions cover the connection of the control cables and the connection of the 
measurement cables to the RF or DC probes used to contact the device under test 
(MOSFET). The connection overview of the pulsed IV test system is shown in 
Figure 2-5 and 2-6. Figure 2-6 is the connection diagram of the DC + pulsed IV test 
system and is effective only for the system installed with the option B1542A-024.

•

“Installing Instruments”

•

“Connecting GPIB Cables”

•

“Installing Pulsed IV Test System” 
See this section if you install the B1542A without the option B1542A-024.

•

“Installing DC + Pulsed IV Test System” 
See this section if you install the B1542A with the option B1542A-024.

•

“Connecting RF Probes”

•

“Connecting DC Probes”

Installing Instruments

The pulsed IV test system uses the DC source monitor, pulse generator, 
oscilloscope, and switch controller with switch units. Install the instruments to the 
appropriate place. See Figure 2-4 for example. For more information, see the 
manual of each instrument. It provides the required environment and the necessary 
and unique information for the instrument. The switch controller and switch units 
are required only for the DC + pulsed IV test system or the option B1542A-024.

Connecting GPIB Cables

Connect the instruments by using the GPIB cables. The pulsed IV test system needs 
two cables and the DC + pulsed IV test system needs three cables.

1. Connect the GPIB cable between the DC source monitor and the pulse generator.

2. Connect the GPIB cable between the oscilloscope and one of above instruments.

3. Only for the DC + pulsed IV test system. Connect the GPIB cable between the 

11713A switch controller and one of above instruments.

Содержание B1542A



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды