Agilent Technologies B1542A Скачать руководство пользователя страница 43

Страница: 43 / 162

Agilent B1542A User’s Guide, Edition 4

2- 23

Installation

Software Installation

Updating Software

Perform the following procedure to update the pulsed IV system software.

1. Install the latest revision of the pulsed IV system software. See “Installing

Software” on page 2-21.

2. Launch EasyEXPERT or Desktop EasyEXPERT. And click the Start

EasyEXPERT button.

3. Open your workspace or create a new workspace.

4. Display the Application Test tab screen.

5. Remove checks from categories except for the Pulsed IV in the Category list.

6. Right-click a pulsed IV test definition in the Library list and click Delete

Definition of This Test to open the confirmation dialog box. And click OK to
delete the test definition from the present workspace.

Repeat this to delete all of the pulsed IV test definitions.

7. Import the pulsed IV test definitions from the following folder.

C:\Program Files\Agilent\PLSDIV\TestDefinitions

NOTE

You do not need to perform “Installing Cable Compensation Data” on page 2-21
and “Compensation” on page 3-11.

If You Remove Pulsed IV Software

Launch the Add or Remove Programs from the Control Panel and remove the
programs in the following order.

1. Agilent Technologies PLSDIV Drain Setup

2. Agilent Technologies B1542A-Opt003

3. Agilent Technologies PLSDIV A.01.02

4. Agilent Technologies PLSDIV A.01.00 or A.01.01

Содержание B1542A



































































































































































Результаты поиска

Содержание B1542A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies B1542A, Руководство пользователя

Результаты поиска

Содержание B1542A

Отзывы:

Бренды по названию

Популярные бренды