Agilent Technologies 3070 Series Скачать руководство пользователя страница 143

Страница: 143 / 410

Agilent Technologies 1989–2002

Agilent 3070 / 79000 Site Preparation

8-15

Chapter 8: Site Preparation – Communications Cabling Requirements: Gathering Configuration Information for MS Windows Networking

DNS

■

Hostname

The name by which this system will be known under DNS is the same as the

Computer Name, or

Task 1

DNS

■

Domain

The domain in which this machine will operate. This domain is associated with
your TCP/IP address.

DNS

■

DNS Service Search Order

IP Addresses (in order) of DNS servers that this system uses for resolving host
names.

DNS

■

Domain Suffix Search Order

Ordered domain suffix list used when searching for a host.

Will WINS Be Used?

(Windows Internet Name Services)

[ ] Yes [ ] No

If no, go to

Task 16

(

Will Other Network Protocols Be Configured?

WINS Address

■

Primary WINS Server

■

Secondary WINS Server

WINS Address

■

Checkboxes

[ ] Enable DNS for Windows
Resolution
[ ] Enable LMHOSTS Lookup

Check or uncheck either of these boxes as applicable.

CAUTION

✸

If configuring for DNS, check

Enable DNS for Windows

Resolution

Table 8-2

Windows NT LAN configuration information (continued)

Task (Network Parameter)

Write System Information Here Description

Содержание 3070 Series



























































































































































































































































































































































































































Результаты поиска

Содержание 3070 Series

Отзывы:

Похожие инструкции для 3070 Series

Бренды по названию

Популярные бренды

Agilent Technologies 3070 Series, Подготовка площадки

Результаты поиска

Содержание 3070 Series

Отзывы:

Похожие инструкции для 3070 Series

Бренды по названию

Популярные бренды