57
ACCU 14
2
0
ACCU 14
2
0
Maintenance
Manuel de l'opérateur
Mantenimiento
Manual para el Operador
6
Maintenance.
Cette machine est conçue pour vous donner un ser-
vice de longue durée.
Dans le mode de démarrage, l’opérateur doit vérifier
que tous les indicateurs et affichages s’allument.
Si l’opérateur éteint correctement la machine (Chapi-
tre 5.2.3) après son utilisation, aucune maintenance
supplémentaire n’est nécessaire.
Cette machine ne doit pas être ouverte par l’opéra-
teur, sauf selon les instructions ci-après.
6.1
Stockage.
Lorsque la machine est entreposée pendant plusieurs
semaines ou plus, préparer correctement la machine:
•
Éteindre correctement la machine, se reporter au
Chapitre 5.2.3.
•
Retirer l’arbre fileté du plateau.
•
Graisser les filets et les cônes avec une huile lé-
gère non corrosive.
•
Envelopper les pièces graissées de papier pour les
protéger contre les poussières.
Nettoyer les pièces graissées lorsque vous désirez
réutiliser la machine.
6.2
Changement du fusible sec-
teur:
Se reporter à la Figure 6.2-1.
•
Éteindre la machine.
•
Débrancher le câble de la prise secteur.
•
Débrancher le câble de la machine.
•
Pincer la languette au centre du porte-fusible et ti-
rer vers le haut.
•
Retirer le porte-fusible (1).
•
Remplacer le fusible par un autre de valeur identi-
que.
•
Replacer le porte-fusible dans la machine.
6.3
Procédure de calibration.
Ce chapitre contient les procédures de calibration ac-
cessibles à l’utilisateur.
Remarque:
Aucune roue ni flasque de blocage
ne doit être montée sur l’arbre de
l’équilibreuse (Figure 6.3.1-1).
6.3.1
Calibration utilisateur.
Utiliser cette fonction si la qualité de l’équilibrage n’est
pas optimale. Ceci lorsque les roues sont correcte-
ment équilibrées mais un déséquilibre est toujours res-
senti lors de la conduite.
•
Eteindre la machine.
•
Allumer la machine, en maintenant la touche “CAL”
enfoncée jusqu’à ce que l’afficheur montre “CAL
6.2
Cambiar el fusible de la red
eléctrica:
Consultar la Figura 6.2-1.
•
Apagar la unidad.
•
Desenchufar el cable de la toma de corriente.
•
Retirar el cable de corriente de la clavija del cable
de la red eléctrica.
•
Pulse el labio, centrado en el soporte del fusible,
hacia arriba.
•
Tire del soporte del fusible hacia afuera.
•
Substituya el fusible (1) por uno de potencia idénti-
ca.
•
Ponga la unidad en su estado original.
6
Mantenimiento.
Esta unidad está diseñada para durar mucho tiempo.
Durante el modo de arranque el operador deberá com-
probar si todos los indicadores y pantallas están en-
cendidos.
Si el operador apaga correctamente (Capitulo 5.2.3)
al final de su turno, no es necesario hacer un manteni-
miento adicional
Excepto en lo que se refiere a los instrucciones si-
guientes, el operadora no abrirá esta unidad.
6.1
Almacenamiento.
Cuando se vaya a guardar la unidad durante varias
semanas o más, prepárela adecuadamente:
•
Apague la unidad correctamente, consultar el Ca-
pítulo 5.2.3.
•
Retirar la cabeza de árbol de la pestaña
•
Emplear un aceite ligero, no-corrosivo oil en todas
las roscas y conos.
•
Envuelva en papel las piezas con aceite para man-
tenerlas sin polvo.
Al volver a trabajar con la unidad, limpie todas las par-
tes con aceite.
6.3
Procedimiento de Calibrado.
En este capítulo se incluyen los procedimiento de ca-
librado a los que el usuario puede acceder.
Nota:
No se debe colocar ninguna rueda ni
arandela de bloqueo sobre el árbol de la
equilibradora (Figura 6.3.1-1).
6.3.1
Calibración Usuario.
Utilice esta función en caso de que el proceso de equi-
librado no sea óptimo. Esto sucede cuando las rue-
das son equilibradas adecuadamente en la unidad
pero, al conducir se sigue sintiendo el desequilibrio.
•
Apague la unidad
•
Encienda la máquina, manteniendo pulsada la tecla
“CAL” hasta que la pantalla muestre el mensaje
“CAL USR” parpadeante y, sucesivamente, el
Содержание 1400
