manualshive.com logo in svg

ACCRETECH UF190R, Руководство пользователя

Поделиться
Скачать
ACCRETECH UF190R Скачать руководство пользователя страница 18

1    Operation Points and Startup

 

 

1-9

1.8 Prober 

Startup

 

“Startup” refers to the procedures from power-up to the completion of prober initialization.   

 

 

 

 

 

When the POWER ON switch is pressed and lit, the 
initialization screen (shown on left) is displayed. 

 

 

The “Operation mode” can be set to [Operator], 
[Engineer], [Manager] or [System], depending on the 
nature of the prober operation and on the skill level of 
the user. (By default, [Operator] is selected at 
power-up.)

 

 

To change the operation mode, touch the <System 
Mode Change> button. The second screen shown on 
the left is displayed. 

 

 

Touch the switch for [Engineer], [Manager] or [System], 
and input the preset password (up to 8 alphanumeric 
characters) to switch the operation mode. (The 
password for each operation level is set to ‘12345678’ 
at shipment. Passwords are registered as part of the 
[Prober Configuration Data]. Engineer level data can 
contain the password for the Engineer level only; 
Manager level data can contain a password each for 
both the Engineer level and the Manager level.) 

 

 

Input the password (the password is not shown on the 
screen) and touch the <ENT> button. You will be 
returned to the initialization screen. In the Engineering 
mode, <Config. Data Change> and <Init. All Axes> 
buttons become available. In the Manager and System 
mode, <Mainte/Adjust> button further becomes 
available. 

 

 

Touch the <START> button on the initialization screen 
to start the initialization of the prober.   

If there is a wafer left in the loader unit, an error will 
result. The wafer is transferred to the inspection tray, 
and an ejection request is displayed. A wafer left on the 
chuck also causes an error. The chuck is moved to the 
front door, and a wafer ejection request is displayed. 
Touch the ALARM OFF key to stop the buzzer, and 
follow the instructions on the screen. 

 

 

 

Содержание UF190R









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды