ABB Relion SAM600 Скачать руководство пользователя страница 78

Страница: 78 / 92

To be able to set the function block TESTMODE remotely, the setting via path

on LHMI and in PST: Main menu/Configuration/Communication/ Station

Communication/IEC61850-8-1/IEC61850-8-1:1

RemoteModControl may not be

set to

Off. The possible values of the parameter RemoteModControl are Off,

Maintenance or All levels. The Off value denies all access to function block

TESTMODE from remote,

Maintenance requires that the category of the

originator (orCat) is

Maintenance and All levels allow any orCat.

The DataObject Mod of the Root LD.LNN0 can be set on the LHMI under Main menu/Test/

Function test modes/Communication/Station communication/IEC61850 LD0 LLN0/

LD0LLN0:1 to

On, Off, TestBlocked,Test or Blocked.

When the setting of the DataObject Mod is changed at this level, all Logical Nodes inside the

logical device update their own behavior according to IEC61850-7-4. The supported values of

the function block TESTMODE are described in

Communication protocol manual, IEC 61850

Edition 2. When the function block TESTMODE is in test mode the Start LED on the LHMI is

turned on with steady light.

The parameter

Mod of any specific function block can be configured under Main menu/Test/

Function test modes/Communication/Station Communication

The parameter Mod can be set on the LHMI to the same values as for the DataObject Mod of

the Root LD.LNN0 to

On, Off, TestBlocked,Test or Blocked. For Example, Main menu/ Test/

Function test modes/ Differential protection/GeneratorDiff(87G,3Id/I>)/ GENPDIF(87G,3Id/

I>):1.

It is possible that the behavior of the function block TESTMODE is also influenced by other

sources as well, independent of the mode communicated via the IEC61850-8-1 station bus. For

example the insertion of the test handle into the test switch with its auxiliary contact is

connected to a BI on the IED and further inside the configuration to the input IED_TEST on the

function block TESTMODE. Another example is when loss of Service Values appears, or as

explained above the setting via the LHMI.

When setting via PST or LHMI the parameter

Operation of any function in an IED is set to Off,

the function is not executed and the behavior (beh) is set to

Off and it is not possible to

override it. When a behavior of a function is

Off the function will not execute. The related Mod

keeps its current state.

When IEC 61850 Mod of a function is set to

Off or Blocked, the Start LED on the

LHMI will be set to flashing to indicate the abnormal operation of the IED.

The IEC 61850-7-4 gives a detailed overview over all aspects of the test mode and other states

of mode and behavior. The status of a function block behavior

Beh is shown on the LHMI under

the Main menu/Test/Function status/Function group/Function block descriptive name/LN

name/Outputs.

•

When the

Beh of a function block is set to Test, the function block is not blocked and all

control commands with a test bit are accepted.

•

When the

Beh of a function block is set to Test/blocked, all control commands with a test

bit are accepted. Outputs to the process via a non-IEC 61850 link data are blocked by the

function block. Only process-related outputs on function blocks related to primary

equipment are blocked. If there is an XCBR function block used, the outputs

EXC_Open

and

EXC_Close are blocked.

•

When the

Beh of a function block is set to Blocked, all control commands with a test bit

are accepted. Outputs to the process via a non-IEC 61850 link data are blocked by the

function block. In addition, the function block can be blocked when their

Beh is blocked.

This can be done if the function block has a block input.

Section 9

1MRK 511 445-UEN B

Basic IED functions

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды