ABB Relion SAM600 Скачать руководство пользователя страница 14

Страница: 14 / 92

The engineering manual contains instructions on how to engineer the IEDs using the various

tools available within the PCM600 software. The manual provides instructions on how to set

up a PCM600 project and insert IEDs to the project structure. The manual also recommends a

sequence for the engineering of protection and control functions, as well as communication

engineering for IEC 61850.

The installation manual contains instructions on how to install the IED. The manual provides

procedures for mechanical and electrical installation. The chapters are organized in the

chronological order in which the IED should be installed.

The commissioning manual contains instructions on how to commission the IED. The manual

can also be used by system engineers and maintenance personnel for assistance during the

testing phase. The manual provides procedures for the checking of external circuitry and

energizing the IED, parameter setting and configuration as well as verifying settings by

secondary injection. The manual describes the process of testing an IED in a substation which

is not in service. The chapters are organized in the chronological order in which the IED should

be commissioned. The relevant procedures may be followed also during the service and

maintenance activities.

The operation manual contains instructions on how to operate the IED once it has been

commissioned. The manual provides instructions for the monitoring, controlling and setting of

the IED. The manual also describes how to identify disturbances and how to view calculated

and measured power grid data to determine the cause of a fault. The manual provides

information related to the need of LHMI service kit to monitor diagnostics and make

configuration changes.

The application manual contains application descriptions and setting guidelines sorted per

function. The manual can be used to find out when and for what purpose a typical protection

function can be used. The manual can also provide assistance for calculating settings.

The technical manual contains operation principle descriptions, and lists function blocks, logic

diagrams, input and output signals, setting parameters and technical data, sorted per

function. The manual can be used as a technical reference during the engineering phase,

installation and commissioning phase, and during normal service.

The communication protocol manual describes the communication protocols supported by

the IED. The manual concentrates on the vendor-specific implementations.

The cyber security deployment guideline describes the process for handling cyber security

when communicating with the IED. Certification, Authorization with role based access control,

and product engineering for cyber security related events are described and sorted by

function. The guideline can be used as a technical reference during the engineering phase,

installation and commissioning phase, and during normal service.

1.3.2

Document revision history

GUID-7099E1DB-1CD6-4037-A418-92AB57FA9462 v3

Document

revision

Date

Product revision

History

2017-12

2.2.1

First release for product version 2.2

2019-05

2.2.1

PTP enhancements and corrections

Section 1

1MRK 511 445-UEN B

Introduction

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды