ABB Relion SAM600 Скачать руководство пользователя страница 53

Страница: 53 / 92

LOAccCurrPwr: Lockout limit setting for accumulated energy.

SpChAlmTime: Time delay for spring charging time alarm.

tDGasPresAlm: Time delay for gas pressure alarm.

tDGasPresLO: Time delay for gas pressure lockout.

DirCoef: Directional coefficient for circuit breaker life calculation.

RatedOperCurr: Rated operating current of the circuit breaker.

RatedFltCurr: Rated fault current of the circuit breaker.

OperNoRated: Number of operations possible at rated current.

OperNoFault: Number of operations possible at rated fault current.

CBLifeAlmLevel: Alarm level for circuit breaker remaining life.

AccSelCal: Selection between the method of calculation of accumulated energy.

OperTimeDelay: Time delay between change of status of trip output and start of main contact

separation.

5.4

Disturbance report DRPRDRE

IP14584-1 v2

5.4.1

Identification

M16055-1 v9

Function description

IEC 61850 identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Disturbance report

DRPRDRE

Disturbance report

A4RADR

Disturbance report

B1RBDR - B22RBDR

5.4.2

Application

M12152-3 v10

To get fast, complete and reliable information about disturbances in the primary and/or in the

secondary system it is very important to gather information. It is also important having a

continuous event-logging to be able to monitor in an overview perspective. These tasks are

accomplished by the disturbance report function DRPRDRE and facilitate a better

understanding of the power system behavior and related primary and secondary equipment

during and after a disturbance. An analysis of the recorded data provides valuable information

that can be used to explain a disturbance, basis for change of IED setting plan, improve

existing equipment, and so on. This information can also be used in a longer perspective when

planning for and designing new installations, that is, a disturbance recording could be a part

of Functional Analysis (FA).

Disturbance report DRPRDRE, always included in the IED, acquires sampled data of all selected

analog and binary signals connected to the function blocks that is,

•

10 internal derived analog signals, and

•

352 binary signals

1MRK 511 445-UEN B

Section 5

Monitoring

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды