ABB Relion SAM600 Скачать руководство пользователя страница 55

Страница: 55 / 92

Event list

Event recorder

Indications

Disturbance

recorder

A4RADR

BxRBDR

Disturbance Report

Binary signals

DRPRDRE

IEC17000113-1-en.vsdx

Analog signals

IEC17000113 V1 EN-US

Figure 7:

Disturbance report functions and related function blocks

For Disturbance report function there are a number of settings which also influences the sub-

functions.

LED indications placed above the LCD screen are not available for use in

SAM600–IO.

Three LED indications placed above the LCD screen makes it possible to get quick status

information about the IED.

Green LED:

Steady light

In Service

Flashing light

Internal failure

Dark

No power supply

Yellow LED:

Steady light

Triggered on binary signal N with SetLEDx = Start (or Start

and Trip)

Flashing light

The IED is in test mode

Red LED:

Steady light

Triggered on binary signal N with SetLEDx = Trip (or Start

and Trip)

Flashing

The IED is in configuration mode

1MRK 511 445-UEN B

Section 5

Monitoring

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды