ABB Relion SAM600 Скачать руководство пользователя страница 52

Страница: 52 / 92

Since there is no current measurement in SAM600-IO, evaluation of the

following parameters are not possible in the circuit breaker condition

monitoring function (SSCBR):

•

Circuit breaker status

•

Remaining life of the circuit breaker

•

Contact erosion estimation

•

Circuit breaker contact travel time

Ensure that OPENPOS, CLOSEPOS, INVDPOS, CBLIFEAL, IPOWALPH,

IPOWLOPH, TRVTOPAL and TRVTCLAL signals are not used in SAM600–IO.

5.3.3.1

Setting procedure on the IED

GUID-4E895FEA-74BF-4B11-A239-0574F8FF5188 v5

The parameters for breaker monitoring (SSCBR) can be set via Protection and Control Manager

(PCM600).

Common base IED values for primary current (

IBase), primary voltage (UBase) and primary

power (

SBase) are set in Global base values for settings function GBASVAL.

GlobalBaseSel: It is used to select a GBASVAL function for reference of base values.

PhSel: It is used to select different phase values.

IBase: Base phase current in primary A. This current is used as reference for current settings.

InitCounterVal: Initial value for number of operations

InitAccCurrPwr: Initial value for accumulated I^CurrExponent integr over CB open travel time

value.

InitInactDays: Initial value for inactive days.

InactiveAlHrs: Alarm time for inactive days counter in hours.

InitCBRemLife: Initial value for remaining life estimates.

InactiveAlDays: Alarm level for inactive days counter.

OpenTimeCorr: Correction factor for circuit breaker opening travel time.

CloseTimeCorr: Correction factor for circuit breaker closing travel time.

tTrOpenAlm: Setting of alarm level for opening travel time.

tTrCloseAlm: Setting of alarm level for closing travel time.

OperAlmLevel: Alarm limit for number of mechanical operations.

OperLOLevel: Lockout limit for number of mechanical operations.

CurrExponent: Current exponent setting for energy calculation. It varies for different types of

circuit breakers. This factor ranges from

0.5 to 3.0.

AccStopCurr: RMS current setting below which calculation of energy accumulation stops. It is

given as a percentage of

IBase.

ContTrCorr: Correction factor for time difference in auxiliary and main contacts' opening time.

AlmAccCurrPwr: Setting of alarm level for accumulated energy.

Section 5

1MRK 511 445-UEN B

Monitoring

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды