ABB Relion SAM600 Скачать руководство пользователя страница 66

Страница: 66 / 92

Control

Protection

Control

Protection

Control and protection

GOOSE

en05000734.vsd

Station HSI

MicroSCADA

Gateway

IED

IEC05000734 V1 EN-US

Figure 12: Example of a broadcasted GOOSE message

7.1.2

Setting guidelines

SEMOD55317-5 v7

There are two settings related to the IEC 61850–8–1 protocol:

Operation: User can set IEC 61850 communication to On or Off.

GOOSEPortEd1: Selection of the Ethernet link where GOOSE traffic shall be sent and received.

This is only valid for Edition 1 and can be ignored if Edition 2 is used. For Edition 2, the

Ethernet link selection is done with the Ethernet Configuration Tool (ECT) in PCM600.

7.1.3

Horizontal communication via GOOSE

7.1.3.1

Sending data

GUID-9888ECAD-8221-4B31-A443-EB1E3A9022C4 v1

In addition to the data object and data attributes of the logical nodes, it is possible to send

the outputs of the function blocks using the generic communication blocks. The outputs of

this function can be set in a dataset and be sent in a GOOSE Control Block to other subscriber

IEDs. There are different function blocks for different type of sending data.

Generic communication function for Single Point indication SPGAPC, SP16GAPC

SEMOD55999-1 v4

Application

SEMOD55350-5 v8

Generic communication function for Single Point Value (SPGAPC) function is used to send one

single logical output to other systems or equipment in the substation. SP16GAPC can be used

to send up to 16 single point values from the application functions running in the same cycle

time. SPGAPC has one visible input and SPGAPC16 has 16 visible inputs that should be

connected in the ACT tool.

Setting guidelines

SEMOD55376-5 v5

There are no settings available for the user for SPGAPC.

Generic communication function for Measured Value MVGAPC

SEMOD55402-1 v3

Section 7

1MRK 511 445-UEN B

Station communication

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды