ABB Relion SAM600 Скачать руководство пользователя страница 34

Страница: 34 / 92

4.1.2.1

Three-phase tripping

M14828-7 v10

Connect the inputs from the protection functions to the input TRIN. The TMGAPC function

block is used to combine up to 32 inputs into one output. Connect the output TRIP to the

binary outputs on the IO board.

This signal can also be used for other purposes internally in the IED. An example could be the

starting of breaker failure protection. The three outputs TRL1, TRL2, TRL3 will always be

activated at every trip and can be utilized on individual trip outputs if single-phase operating

devices are available on the circuit breaker even when a three-phase tripping scheme is

selected.

Set the function block to

Program = 3 phase and set the required length of the trip pulse to for

example,

tTripMin = 150ms.

The typical connection is shown below in figure

BLOCK
BLKLKOUT
TRIN
TRINL1
TRINL2

TRINL3
PSL1
PSL2
PSL3
1PTRZ
1PTREF
P3PTR
SETLKOUT

RSTLKOUT
STDIR

TRIP

SMPPTRC

TRL1
TRL2
TRL3

TR1P
TR2P
TR3P

CLLKOUT

START

STL1
STL2
STL3

REV

Protection functions with 3 phase
trip, for example time delayed
overcurrent protection

TMAGAPC

STN

IEC05000544-4-en.vsdx

IEC05000544 V4 EN-US

Figure 4:

Tripping logic SMPPTRC is used for a simple three-phase tripping application

4.1.2.2

Single- and/or three-phase tripping

M14828-11 v7

The single-/three-phase tripping operation mode will give single-phase tripping for single-

phase faults and three-phase tripping for multi-phase fault. This operating mode is always

used together with a single-phase autoreclosing scheme.

The single-phase tripping operation mode can include different options and the use of the

different inputs in the function block. Inputs TRINL1, TRINL2 and TRINL3 shall be used for trip

signals from functions with built-in phase selection logic such as distance or line differential

protection functions.

The inputs 1PTRZ and 1PTREF are used for single-phase tripping from functions which do not

have built-in phase selection logic:

•

1PTRZ can be connected to the carrier aided trip signal from the distance protection

scheme (it means that another distance protection function has seen or detected the

fault)

•

1PTREF can be connected to an earth fault function such as EF4PTOC or a carrier aided

trip signal from the earth fault protection scheme

Section 4

1MRK 511 445-UEN B

Logic

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды