ABB Relion SAM600 Скачать руководство пользователя страница 31

Страница: 31 / 92

Refer to Table

for the description of the input-output relationship in terms of the value and

the quality attributes.

Table 4:

Description of the input-output relationship

VALID

OPEN

CLOSE

POSITION

Value

Description

Intermediate

Open

Closed

Bad State

3.4.3

Setting guidelines

SEMOD55398-5 v5

The function does not have any parameters available in the PCM600.

3.5

Single point generic control 8 signals SPC8GAPC

SEMOD176448-1 v3

3.5.1

Identification

SEMOD176456-2 v3

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Single point generic control 8 signals

SPC8GAPC

3.5.2

Application

SEMOD176511-4 v7

The Single point generic control 8 signals (SPC8GAPC) function block is a collection of 8 single

point commands that can be used for direct commands for example putting IED in

"ChangeLock" state from remote. In this way, simple commands can be sent directly to the IED

outputs, without confirmation. Confirmation (status) of the result of the commands is

supposed to be achieved by other means, such as binary inputs and SPGAPC function blocks.

PSTO is the universal operator place selector for all control functions. Even if

PSTO can be configured to allow LOCAL or ALL operator positions, the only

functional position usable with the SPC8GAPC function block is REMOTE.

3.5.3

Setting guidelines

SEMOD176518-4 v7

The parameters for the single point generic control 8 signals (SPC8GAPC) function are set via

PCM600.

Operation: turning the function operation On/Off.

There are two settings for every command output (totally 8):

PulseModex: decides if the command signal for output x is Latched (steady) or Pulsed.

1MRK 511 445-UEN B

Section 3

Control

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды