ABB Relion SAM600 Скачать руководство пользователя страница 74

Страница: 74 / 92

IEC17000158-1-en.vsdx

IEC17000158 V1 EN-US

Figure 14: IED summary

However, the following information is available only on the product label:

•

OrderingNo

•

ProductionDate

This information is very helpful when interacting with ABB product support (for example

during repair and maintenance).

9.2.2

Factory defined settings

M11789-39 v11

The factory defined settings are very useful for identifying a specific version and very helpful in

the case of maintenance, repair, interchanging IEDs between different Substation Automation

Systems and upgrading. The factory made settings can not be changed by the customer. They

can only be viewed. The settings are found in the local HMI under Main menu/Diagnostics/IED

status/Product identifiers

The following identifiers are available:

•

ProductType
•

Describes the type of IED. Example:

SAM600–IO

•

ProductDef
•

Describes the release number from the production. Example:

2.2.1.0

•

FirmwareVer
•

Describes the firmware version. Example:

2.2.1.9

•

Firmware version numbers run independently from the release production numbers.

For every release number there can be one or more firmware versions depending on

the small issues corrected in between releases.

•

ProductVer
•

Describes the product version. Example:

2.2.1

Section 9

1MRK 511 445-UEN B

Basic IED functions

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды