ABB Relion SAM600 Скачать руководство пользователя страница 75

Страница: 75 / 92

1 is the Major version of the manufactured product this means, new platform of the product

2 is the Minor version of the manufactured product this means, new functions or new hardware

added to the product

3 is the Major revision of the manufactured product this means, functions or hardware is either

changed or enhanced in the product

•

IEDMainFunType
•

Main function type code is present but not used because there is no IEC 60870-5-103

protocol in SAM600-IO.

•

SerialNo

9.3

Measured value expander block RANGE_XP

SEMOD52451-1 v2

9.3.1

Identification

SEMOD113212-2 v3

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Measured value expander block

RANGE_XP

9.3.2

Application

SEMOD52434-4 v6

The IEC 61850 generic communication I/O functions (MVGAPC) are provided with

measurement supervision functionality. All measured values can be supervised with four

settable limits, that is low-low limit, low limit, high limit and high-high limit. The measure value

expander block ( RANGE_XP) has been introduced to be able to translate the integer output

signal from the measuring functions to 5 binary signals, that is below low-low limit, below low

limit, normal, above high-high limit or above high limit. The output signals can be used as

conditions in the configurable logic.

9.3.3

Setting guidelines

SEMOD113223-4 v1

There are no settable parameters for the measured value expander block function.

9.4

Parameter setting groups

IP1745-1 v1

9.4.1

Application

M12007-6 v10

Six sets of settings are available to optimize IED operation for different power system

conditions. By creating and switching between fine tuned setting sets from the configurable

binary inputs, results in a highly adaptable IED that can cope with a variety of power system

scenarios.

Different conditions in networks with different voltage levels require highly adaptable

protection and control units to best provide for dependability, security and selectivity

requirements. Protection units operate with a higher degree of availability, especially, if the

setting values of their parameters are continuously optimized according to the conditions in

the power system.

1MRK 511 445-UEN B

Section 9

Basic IED functions

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды