ABB Relion SAM600 Скачать руководство пользователя страница 49

Страница: 49 / 92

Section 5

Monitoring

5.1

Gas medium supervision SSIMG

GUID-358AD8F8-AE06-4AEA-9969-46E5299D5B4B v3

5.1.1

Identification

GUID-AD96C26E-C3E5-4B21-9ED6-12E540954AC3 v4

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Insulation gas monitoring function

SSIMG

5.1.2

Application

GUID-A840E38C-CC42-4995-A569-A6092DDB81B2 v5

Gas medium supervision (SSIMG) is used for monitoring the circuit breaker condition. Proper

arc extinction by the compressed gas in the circuit breaker is very important. When the

pressure becomes too low compared to the required value, the circuit breaker operation shall

be blocked to minimize the risk of internal failure. Binary information based on the gas

pressure in the circuit breaker is used as an input signal to the function. The function

generates alarms based on the received information.

5.1.3

Setting guidelines

GUID-DF6BEC98-F806-41CE-8C29-BEE9C88FC1FD v3

The parameters for Gas medium supervision SSIMG can be set via Protection and Control

Manager PCM600.

Operation: This is used to disable/enable the operation of gas medium supervision i.e. Off/On.

PresAlmLimit: This is used to set the limit for a pressure alarm condition in the circuit breaker.

PresLOLimit: This is used to set the limit for a pressure lockout condition in the circuit breaker.

TempAlarmLimit: This is used to set the limit for a temperature alarm condition in the circuit

breaker.

TempLOLimit: This is used to set the limit for a temperature lockout condition in the circuit

breaker.

tPressureAlarm: This is used to set the time delay for a pressure alarm indication, given in s.

tPressureLO: This is used to set the time delay for a pressure lockout indication, given in s.

tTempAlarm: This is used to set the time delay for a temperature alarm indication, given in s.

tTempLockOut: This is used to set the time delay for a temperature lockout indication, given in

tResetPressAlm: This is used for the pressure alarm indication to reset after a set time delay in

tResetPressLO: This is used for the pressure lockout indication to reset after a set time delay

in s.

tResetTempLO: This is used for the temperature lockout indication to reset after a set time

delay in s.

1MRK 511 445-UEN B

Section 5

Monitoring

Switchgear control unit SAM600-IO

Application manual

Содержание Relion SAM600




























































































Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion SAM600, Руководство по применению

Результаты поиска

Содержание Relion SAM600

Отзывы:

Бренды по названию

Популярные бренды