54
40019121
mode
boost
mode
boost
mode
boost
mode
boost
mode
boost
mode
boost
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
mode
Press for
5 seconds
on the
+
NH\
Appliance
search
WDNHV
about
one
minute
.
mode
mode
mode
mode
mode
boost
n
o
p
q
r
s
If pairing fails, the display on the
FRQWUROJRHVEDFNWR
rF 0
. Start the pairing
procedure again by pressing the
+
NH\IRU
5 seconds
.
&KHFNEHIRUHKDQGWKDWWKHUHFHLYHUXQLWLVVWLOOUHDG\IRU
SDLULQJWKH/('VKRXOGÀDVKSLQN
If the radiator is still not paired to the remote control
after three attempts, the remote control
and receiverneed to be reset
(see
chapter 8.3
).
Pairing
complete.
The remote
control goes
WR)URVWIUHH
mode. The
FORFNLFRQ
ZLOOÀDVKXQWLO
the date and time are set.
A remote
control which has
already been paired
cannot be paired again.
If an attempt to do so
is made, the receiver
flashes white
3 times
.
If the remote control is too far away from the heating appliance, the latter will continue to
operate in the last mode sent by the controller. Changes of mode relating to the opera-
tion of a programme or manual boosts will however continue as normal.
The appliance will resume normal operations within a few seconds when the remote
control is within range again (
within 10 metres
).
A) Procedure using the receiver unit on your appliance:
Press
twice
on the LED on your appliance (4 seconds max for the
2 presses).
The LED is
ÀDVKLQJSLQN
.
You then have
one minute
to pair your appliance with the remote
control.
B) Remote control procedure:
(if the remote control screen is off, turn it on by pressing a key)
NOTE:
Operations A and B
can be done in any
order.
x
x
x
x
)URVWIUHHPRGH
Synchronisation
55
02/2019
ÀDVKLQJSLQN
4.3 Status of LED (on radiator or towel dryer)
STATUS
COLOUR
Fixed
Flashing
Off
Green
Eco mode
x
Standby
x
Powered down
x
Stop (pilot wire)
x
Stop load
shedding (pilot
wire)
Red
Comfort mode
Boost
Blue
)URVWIUHHPRGH
Load shedding (pilot wire)
Open window
detected
Yellow
T° override°
(+ colour
sequence)
Error: contact
after-sales service
Pink
Pairing error /
Appliance not paired
Pairing underway
4.4 Remote control displays
Operating Modes
Scroll through times of day (prog)
Days of the
ZHHN
SURJ
Pro
g
mode
Setpoint
temperature
NOTE:
6FUHHQOLJKWLQJWXUQVRIIDXWRPDWLFDOO\LIQRNH\KDVEHHQSUHVVHGIRUWKHSDVW
5 seconds
.
The screen goes to standby after
1 minute
.
The standby mode does not affect the functioning of the radiator, and pressing
DQ\NH\ZLOOPDNHWKHVFUHHQOLJKWXSDJDLQ
The screen must be on for the pressing of a key to have an effect
(e.g.
temperature setting, changing a parameter, etc.).
