YOKOGAWA DL1720E Service Manual Download Page 30

Page: 30 / 73

3-1

SM 701730-01E

Adjustments

Chapter 3

Adjustments

3.1

Introduction

The top cover, printer cover, printer case, front bezel, and shield cover must be removed

before adjusting the DL1720E/DL1740E/DL1740EL. Read the warning and cautions

below before doing so.

WARNING

Circuit patterns of the printed circuit board are exposed. Be careful when

handling so that hands or fingers are not injured by the protruding pins.

CAUTION

• Circuit patterns of the printed circuit board are exposed. If these patterns touch

other metallic materials, electrical shorting will occur, causing the circuit to be

damaged or burnt.

• It is sometimes necessary to turn the DL1720E/DL1740E/DL1740EL upside

down for adjustment. Do not drop the instrument, or allow it to fall over.

• When feeding power with the DL1720E/DL1740E/DL1740EL cover open, apply

a flow of air to the AD4 board (or the AD2 board for the DL1720E) and Power

Supply (B8052YA*).

Power Supply of the DL1720E/DL1740E/DL1740EL shipped before May 2005 is
B9989YA, and Power Supply of the DL1720E/DL1740E/DL1740EL shipped since May
2005 is B8052YA.

Summary of Contents for DL1720E










































































Search results

Summary of Contents for DL1720E

Reviews:

Related manuals for DL1720E

Brands by name

Popular brands

YOKOGAWA DL1720E, Service Manual

Search results

Summary of Contents for DL1720E

Reviews:

Related manuals for DL1720E

Brands by name

Popular brands