Yanmar ZT350 series Operation Manual Download Page 8

Page: 8 / 58

General Information

There is no substitute for common sense

and careful practices. Improper practices or

carelessness can cause burns, cuts,

mutilation, asphyxiation, other bodily injury

or death. This information contains general

safety precautions and guidelines that must

be followed to reduce risk to personal safety.

Special safety precautions are listed in

specific procedures. Read and understand

all of the safety precautions before operation

or performing repairs or maintenance.

Before You Operate

DANGER

The safety messages that follow have

DANGER level hazards. These safety

messages describe a hazardous

situation which, if not avoided, will

result in death or serious injury.

NEVER permit anyone to

install or operate the engine or

stern-drive without proper

training.

• Read and understand this Operation

Manual before you operate or service the

engine or stern-drive to ensure that you

follow safe operating practices and

maintenance procedures.

• Safety signs and labels are additional

reminders for safe operating and

maintenance techniques.

• See your authorized Yanmar Marine

dealer or distributor for additional training.

SAFETY

ZT350 Operation Manual

Summary of Contents for ZT350 series



























































Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands

Yanmar ZT350 series, Operation Manual

Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands