Yanmar ZT350 series Operation Manual Download Page 56

Page: 56 / 58

No.

Problem

Possible Cause

Action

Reference Page

Power Trim Does Not

Operate (Electric

Motor Does Not Oper-

ate)

Blown fuse.

Replace the fuse.

Circuit breaker is

tripped.

Wait until the breaker

cools down and the

breaker is restored.

Loose or dirty

electrical connections

or damaged wiring.

Check all associated

electrical connections

and wires (especially

battery cables). Clean

and tighten faulty

connection. Repair or

replace wiring.

Power Trim Does Not

Operate (Electric

Motor Operates but

Stern-drive Does Not

Move)

Trim pump oil level is

low.

Fill pump with oil.

Stern-drive binding in

gimbal ring.

Check for obstruction.

See your authorized

Yanmar Marine dealer

or distributor.

—

TROUBLESHOOTING

ZT350 Operation Manual

Summary of Contents for ZT350 series



























































Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands

Yanmar ZT350 series, Operation Manual

Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands