Yanmar ZT350 series Operation Manual Download Page 41

Page: 41 / 58

◯

: Check or Clean ◊: Replace ●: Contact your authorized Yanmar Marine dealer or distributor

Daily

See Daily

Checks on

page 26

Weekly

Every 50

Hours

Every 100

Hours

Every 250

Hours

Every

Year

Check the Engine

Alignment

●

Lubricate the Unit

Bearing (Gimbal

Housing)

◯

Lubricate the Engine

Coupler***

◯

Check the Circuit for

Loose or Damaged

Connections

◯

Test the Y-CaPS Out-

put on ZT350

◯

Check the Steering

System for Loose,

Missing or Damaged

Parts

◯

Check the Remote

Control for Loose,

Missing or Damaged

Parts

◯

Lubricate the Cables

and the Linkages

◯

Retorque the Rear En-

gine Mounts

◯

If operating in only freshwater, this maintenance may be extended to every four months.

Every 250 hours or every year, whichever comes first.

*** Lubricate engine coupler every 50 hours if operated at idle for prolonged periods of time.

MAINTENANCE

ZT350 Operation Manual

Summary of Contents for ZT350 series



























































Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands

Yanmar ZT350 series, Operation Manual

Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands