Yanmar ZT350 series Operation Manual Download Page 19

Page: 19 / 58

Observe the following precautions when

applying antifouling or marine paint to the

transom of the boat hull:

• ALWAYS follow the paint/coating

manufacturer's directions for surface

preparation and application.

• ALWAYS use a high quality primer and

topcoat paint specifically designed for

aluminum outboards or stern-drives.

• NEVER paint the anodes installed on the

stern-drive.

• NEVER paint the Y-CaPS reference

electrode and / or anode.

• NEVER wash the stern-drive with a high

pressure washer. This could damage the

coating on the reference wire.

• NEVER paint the stern-drive with a

material that contains copper or tin.

• NEVER paint over drain holes, anodes, Y-

CaPS or other items specified by the

anode Manufacturer.

Contact your authorized Yanmar Marine

dealer or distributor for assistance.

NOTICE: Galvanic corrosion damage,

normal maintenance and consumable parts

are not covered by the Yanmar Limited

Warranty.

Additional Protection

In addition to the corrosion protection

devices, take these steps to inhibit

corrosion:

1. Paint the stern-drive. See Touching-Up

the Stern-Drive Paint and Spray with

Corrosion Guard on page 46.

2. Spray stern-drive components on the

inside of the vessel annually with

Corrosion Guard to protect the finish

from dulling and corrosion. External

stern-drive components may also be

sprayed.

3. Keep all lubrication points, especially

the steering system, shift and throttle

linkages, well-lubricated.

4. Flush the coolant system periodically,

preferably after each use.

NOTICE: Replace anodes if eroded 50

percent or more.
NOTICE: Anytime the boat is left in the

water and the engine is not running, the

drive must be left in the fully down

position. This will keep the anodes in the

water and will keep the exhaust pipe

engaged with the exhaust port of the

drive.

(4)

(3)

(2)

(5)

(1)

0005989

Figure 3

1 – Gear Housing Anodic Plates

2 – Ventilation Plate Anode

3 – Y-CaPS Electrode

4 – Trim Cylinder Anodes

5 – Propeller Shaft Anodes

PRODUCT OVERVIEW

ZT350 Operation Manual

Summary of Contents for ZT350 series



























































Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands

Yanmar ZT350 series, Operation Manual

Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands