Yanmar ZT350 series Operation Manual Download Page 54

Page: 54 / 58

Checking the Circuit for Loose or

Damaged Connections

See Checking the Circuit for Loose or

Damaged Connections on page 42.

Testing the Y-CaPS Unit Output

See Yanmar Cathodic Protection System

on page 20.

Checking the Steering System for

Loose, Missing or Damaged Parts

See Checking the Steering System for

Loose, Missing or Damaged Parts on page

42.

Checking the Remote Control for

Loose, Missing or Damaged Parts

See Remote Controls on page 17.

Lubricating the Cable and the

Linkages

See Lubricating the Shift Cable (Typical) on

page 45.

Touching-Up the Stern-Drive Paint

and Spray with Corrosion Guard

See Touching-Up the Stern-Drive Paint and

Spray with Corrosion Guard on page 46.

Changing the Stern-Drive Oil

See Changing the Stern-Drive Oil on page

46.

Retorqueing the Rear Engine

Mounts

See Torqueing the Rear Engine Mount Bolts

on page 44.

MAINTENANCE

ZT350 Operation Manual

Summary of Contents for ZT350 series



























































Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands

Yanmar ZT350 series, Operation Manual

Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands