Yanmar ZT350 series Operation Manual Download Page 35 | Manualshive

Page: 35 / 58

background image

MAINTENANCE

This section of the Operation Manual

describes the procedures for proper care

and maintenance of the stern-drive.

Before you operate the ZT350, read the

following safety information and review the

Safety on page 3.

DANGER

The safety messages that follow have

DANGER level hazards. These safety

messages describe a hazardous

situation which, if not avoided, will

result in death or serious injury.

Crush Hazard

ALWAYS use lifting

equipment with sufficient

capacity to lift the stern-drive.

NEVER stand under a hoisted stern-drive. If

the hoist mechanism fails, the stern-drive

will fall on you, causing serious injury or

death.

NEVER support the stern-drive with

equipment not designed to support the

weight of the stern-drive such as wooden

pieces, blocks or by only using a jack.

ZT350 Operation Manual

31

© 2008 Yanmar Marine International

«
...
33
34
35
36
37
...
»

Summary of Contents for ZT350 series



























































Reviews:

No comments

Related manuals for ZT350 series

Brand: Datavan Pages: 15

Brand: Acrosser Technology Pages: 7

Brand: CIRCUIT DESIGN Pages: 9

661FX7MJ Series

Brand: Foxconn Pages: 81

Brand: P&E Microcomputer Systems Pages: 38

Brand: Atmel Pages: 16

Brand: JETWAY Pages: 44

Brand: Aaeon Pages: 44

Brand: AXIOMTEK Pages: 67

Spartan-7 SP701

Brand: Xilinx Pages: 4

FRDMDUALK3664EVB

Brand: NXP Semiconductors Pages: 17

Brand: Abit Pages: 24

Brand: MSK Pages: 10

MEG Z390 GODLIKE

Brand: MSI Pages: 111

MAG B550M MORTAR WIFI

Brand: MSI Pages: 71

Brand: MSI Pages: 284

MAG B460M BAZOOKA

Brand: MSI Pages: 72

MAG B660M MORTAR WIFI DDR4

Brand: MSI Pages: 403

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands