Yanmar ZT350 series Operation Manual Download Page 13 | Manualshive

Page: 13 / 58

background image

NOTICE

NEVER use the stern-drive lifting eye to lift

the engine and stern-drive as an assembly.

Use the engine lifting eyes to lift the engine

and stern-drive. Only use the stern-drive

lifting eye to lift the stern-drive as a separate

component.

The anode of the stern-drive is only

calculated for the stern-drive. Changing the

material of the propeller may require

additional anodes to be installed on the

stern-drive.

Anytime the boat is left in the water and the

engine is not running, the drive must be left

in the fully down position. This will keep the

anodes in the water and will keep the

exhaust pipe engaged with the exhaust port

of the drive.

SAFETY

ZT350 Operation Manual

9

© 2008 Yanmar Marine International

«
...
11
12
13
14
15
...
»

Summary of Contents for ZT350 series



























































Reviews:

No comments

Related manuals for ZT350 series

Brand: Yamaha Pages: 86

Brand: Atmel Pages: 22

Brand: Advantech Pages: 3

EZ-USB HX2LP CY4605

Brand: Cypress Pages: 2

Brand: J&W Pages: 40

Brand: Micrel Pages: 14

Brand: ASROCK Pages: 27

B550 AORUS ELITE AX V2

Brand: Gigabyte Pages: 12

Brand: Telaire Pages: 4

COMe Ref.Carrier T6

Brand: Kontron Pages: 41

8A 72QFN Series

Brand: IDT Pages: 29

Brand: Atmel Pages: 39

Brand: Gigabyte Pages: 37

Fatal1ty Professional Z97

Brand: ASROCK Pages: 144

Qseven conga-QA5

Brand: Congatec Pages: 61

Brand: Intel Pages: 62

AIMB-742 Socket 478

Brand: Intel Pages: 4

Brand: Commell Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands