Yanmar ZT350 series Operation Manual Download Page 11

Page: 11 / 58

WARNING

Exhaust Hazard

NEVER block windows,

vents, or other means of

ventilation if the engine is

operating in an enclosed area.

All internal combustion

engines create carbon monoxide gas during

operation and special precautions are

required to avoid carbon monoxide

poisoning.

Electrical Shock Hazard

ALWAYS turn off the battery

switch (if equipped) or

disconnect the negative

battery cable before servicing

the equipment.

ALWAYS keep the electrical connectors

and terminals clean. Check the electrical

harnesses for cracks, abrasions, and

damaged or corroded connectors.

CAUTION

The safety messages that follow have

CAUTION level hazards. These safety

messages describe a hazardous

situation which, if not avoided, could

result in minor or moderate injury.

NEVER permit anyone to

install or operate the stern-

drive or engine without proper

training. Safety signs and

labels are additional

reminders for safe service and

maintenance techniques. Read and

understand this Operation Manual before

you operate or service the stern-drive to

ensure that you follow safe servicing

practices and maintenance procedures.

Poor Lighting Hazard

Ensure that the work area is adequately

illuminated. ALWAYS install wire cages on

portable safety lamps.

Tool Hazard

ALWAYS use tools appropriate for the task

at hand and use the correct size tool for

loosening or tightening machine parts.

Flying Object Hazard

ALWAYS wear eye protection

when servicing the stern-drive

or when using compressed air

or high-pressure water. Dust,

flying debris, compressed air,

pressurized water or steam may injure your

eyes.

SAFETY

ZT350 Operation Manual

Summary of Contents for ZT350 series



























































Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands

Yanmar ZT350 series, Operation Manual

Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands